Files tool

Audio & Video Converter and Trimmer

Choose an audio or video file, select a supported output and optionally set a start and end time.

Runs in your browser. No upload.

About this tool

Audio & Video Converter and Trimmer made simple.

The browser checks actual codec support before processing. Output format, sound/video quality and speed vary by device and browser; large clips are best handled on a computer. Your original stays unchanged and files are not uploaded.

Guide

Using Audio & Video Converter and Trimmer

The Audio and Video Converter and Trimmer changes one sound or video file into another format, and can cut out a part of it. You pick a file, choose MP3, M4A, OGG, MP4 or WebM, and optionally give a start and end time in seconds. The work runs in your browser, so the file is not uploaded and your original is not changed. What works depends on the codecs your browser supports, and it cannot repair damaged files or edit scenes.

How to use it

  1. Press Choose an audio or video file and pick a file from your device.
  2. Pick the output: MP3, M4A (AAC) or OGG (Opus) for sound, or MP4 or WebM for video.
  3. To cut a piece, type a start time in seconds. Leave it at 0 to begin at the start. Type an end time to stop earlier, or leave it empty to go to the end.
  4. Press Convert / trim and watch the progress bar. Keep the tab open while it works. Press Cancel to stop.
  5. When the message says the file is ready, use the Download link. Press Clear to remove the file and start again.

Worked examples

Pull the sound out of a video

You enter
File
talk.mp4
Output
MP3
Start
0
End
You get
Download name
talk.mp3
Content
the audio track of the whole video

Choosing an audio output makes the tool read only the audio track and drop the picture. The download name keeps the original name and takes the new extension. This was not run with a real file, so the sound quality is not checked.

Not run through the tool. Treat it as an illustration.

Keep a 15 second piece

You enter
File
interview.m4a
Output
OGG
Start
10
End
25
You get
Length
15 seconds, from second 10 to second 25

The clip begins at 10 seconds and stops at 25, which is 25 minus 10 = 15 seconds long. A real conversion was not run, so the exact cut point is not confirmed.

Not run through the tool. Treat it as an illustration.

An end time that is not later than the start

You enter
Start
5
End
5
You get
Error
End time must be greater than a valid start time.

The check runs before any decoding. I ran it with start 5 and end 5, and with start 10 and end 5, and both were refused. A negative start is refused as well.

Run through the tool’s own code.

How the saved file is named

You enter
File
My Holiday Clip.mov
Output
WebM
You get
Download name
My-Holiday-Clip.webm

The old extension is removed, any run of characters that are not letters, numbers, dot, underscore or hyphen becomes one hyphen, and the name is cut to 80 characters before the new extension is added.

Run through the tool’s own code.

When it helps

  • Extract the sound from a recorded meeting or lecture video to listen to it as an audio file.
  • Turn an audio file into MP3 or M4A so it opens on a device that does not like the original format.
  • Cut a short part out of a long recording before sharing it.
  • Make a WebM or MP4 copy of a clip for a website or an app that wants one of those containers.
  • Check whether your browser can read an unusual audio or video file, without installing software.

Limits to keep in mind

  • Only five outputs exist: MP3, M4A, OGG, MP4 and WebM. The page has no choice for bit rate, resolution, frame rate or codec, and the code uses a fixed medium quality.
  • From the code, MP4 and WebM outputs keep only the video and leave out the sound. Choose an audio output if you need the sound.
  • The browser must be able to read and decode the file. If it cannot, the tool shows an error instead of a result. Results, speed and file size differ between browsers and devices.
  • Large or long files need a lot of memory and time, and a phone may stop. The page suggests a computer for large clips.
  • Saving large output directly to disk works only in browsers that offer a save-file picker. Otherwise untick that option and use the normal download.

Tips

  • Do a short test first. Trim to a 10 or 20 second part and check the result before converting a long file.
  • Use seconds for the times. For 1 minute 30 seconds, type 90.
  • Keep your original file until you have played the converted one all the way through.
  • Close other heavy tabs before you convert a long video, to leave more memory free.
  • If a format fails, try another browser or a computer, because codec support differs between browsers and devices.

Common questions

About Audio & Video Converter and Trimmer.

Does this converter upload my files?

No. The page says media is processed in your browser and files are not uploaded. The conversion code runs on your device and the result is offered as a download. Keep the tab open until it finishes, because closing it stops the work.

Which input formats can I open?

The file picker lists audio and video files such as MP3, M4A, WAV, OGG, FLAC, MP4, MOV, WebM and MKV. Whether a file really opens depends on your browser's codecs. If it cannot be read, the tool tells you to try a common MP4, WebM, MP3, WAV, M4A or OGG file.

How do I extract audio from a video?

Choose the video file and select MP3, M4A or OGG as the output. The tool takes the sound track and drops the picture. If the video has no sound track, it shows the message No audio track was found.

Can I convert audio to video?

No. Video outputs need a video track in the input. If you pick MP4 or WebM for an audio-only file, the tool shows a message that no video track was found and suggests choosing an audio output instead.

Why is my MP4 or WebM copy silent?

In the current code, video outputs are made without the audio track, so the copy has picture only. Use an audio output to get the sound. If you need both together, this tool does not do that at the moment.

How do I trim a clip?

Type a start time and an end time in seconds, then convert. The start counts from the beginning of the file, and the end must be larger than the start. Leave the end empty to run to the end of the file. The original is not changed.

What does the save to disk option do?

It writes the result straight to a file you choose, in pieces, so large outputs do not have to sit in memory. It needs a browser with a save-file picker. If yours has none, the tool says so and you can untick the option.

Will the quality be the same as the original?

No, expect some change. The tool re-encodes the sound or the video with a fixed medium quality setting, so a conversion is not an exact copy. Compare the result with your original by listening or watching before you replace anything.

Why does the conversion fail or stop?

Common reasons are a format the browser cannot decode, a codec it cannot encode, a file too large for your device memory, or pressing Cancel. A message explains which case applies. Try another browser, a smaller piece or a different output format.

Does this audio and video converter upload my files?

No. Supported files are processed in your browser. Keep the tab open; long or high-resolution media may need substantial memory, power and time.

Can I convert every media format?

No. Browser codec support differs by browser and device. The available formats shown by the tool depend on codecs your browser can decode or encode.